Eccentrically Loaded Bolt Group, ICR Method (AISC 360-22)

AISC 360-22 (LRFD)AISC Steel Construction Manual (16th Ed.), Part 7Flag of United States

Find the eccentric bolt-group coefficient C by the instantaneous center of rotation method for any load angle, then the group design strength from the AISC 360-22 bolt shear strength. Every bolt's force, direction and deformation is shown, so the C value can be checked rather than read off a table.

14-day free trial • No credit card required

  • AISC 360-22 (LRFD), AISC Steel Construction Manual (16th Ed.), Part 7

    Named standards on every check

  • Clause on every result

    Formula, inputs and reference visible

What it calculates

Find the eccentric bolt-group coefficient C by the instantaneous center of rotation method for any load angle, then the group design strength from the AISC 360-22 bolt shear strength. Every bolt's force, direction and deformation is shown, so the C value can be checked rather than read off a table.

Who uses this calculator

Engineers checking a bolt group loaded off its centroid, when the load angle falls between the 15-degree steps of the AISC Manual coefficient tables. Every bolt's force and deformation is reported, so coefficient C can be checked instead of interpolated. Rectangular bolt grids with uniform pitch and gage.

How it calculates

The calculator finds coefficient C for a rectangular bolt group under an eccentric load, then multiplies it by the shear design strength of one bolt to get the capacity of the group.

Bolt group and loading

You define a rectangular grid by its number of rows and columns, the vertical pitch and the horizontal gage. Bolt coordinates are measured from the group centroid. The factored shear V_f and axial force H_f each act at their own eccentricity, and together they set the resultant force R_f and the load angle measured from the shear axis. The shear force must be non-zero for the ICR solution.

Instantaneous center of rotation

Under an eccentric load, the bolt group rotates about an instantaneous center. Each bolt deforms in proportion to its distance from that center, and the bolt furthest away reaches the ultimate deformation of 0.34 in. Bolt force follows the load-deformation relationship used in the AISC Manual, acting perpendicular to the line from the instantaneous center to the bolt.

The location of the instantaneous center (y_o, r_o) is solved in the sheet with a two-unknown Newton-Raphson iteration on the moment and force equilibrium equations. This covers both pure shear and combined shear and axial loading.

Coefficient C is the resultant bolt force from the solved distribution, expressed as a multiple of the single-bolt strength.

Bolt shear design strength

The single-bolt design strength uses the nominal shear stress F_nv from ANSI/AISC 360-22 Table J3.2 for the selected bolt group and thread condition, the nominal bolt area and the number of shear planes:

φR_n = 0.75 × F_nv × A_b × number of shear planes

F_nv is reduced by 0.833 when the fastener pattern length exceeds 38 in (Table J3.2, footnote [c]).

Group capacity check

Bolt group shear capacity = C × single-bolt design strength

Demand capacity ratio = R_f / bolt group shear capacity ≤ 1.0

The concentric group strength, with every bolt fully effective, is reported as an upper bound.

Per-bolt results

A results table lists every bolt's position, radius from the instantaneous center, deformation, force ratio, force magnitude, components and direction. The table and the force diagram read the same distribution that produces C, so the coefficient can be traced bolt by bolt.

Validation and scope

The calculator is checked against coefficient values from AISC Manual Tables 7-6, 7-7, 7-8, 7-9, 7-11 and 7-13, at load angles from 0 to 75 degrees. Bearing and tearout of the connected material are out of scope, and irregular bolt patterns are not supported.

Frequently asked questions

Access this calculator and 100+ more

All verified, standards-aligned. Start a free trial - no credit card required.

Linking a calculation to a column in Calcs.com, with the AISC Steel Construction Manual reference attached

We use analytics cookies to understand how you use this site and improve our content. See our privacy policy and cookie policy for details.