Wood Diaphragm Design (LRFD, SDPWS 2021)

AWC SDPWS 2021AWC NDS 2024ASCE 7-22Flag of United States

Design flexible wood structural panel diaphragms to SDPWS 2021 with LRFD. Loads are distributed to any number of braced wall lines by FEA, then checked for unit shear capacity, aspect ratio, chord and collector forces to NDS 2024, nailing zones and in-plane deflection. Wind and seismic loads link in from the wind and seismic calculations.

14-day free trial • No credit card required

  • AWC SDPWS 2021 + 2 more

    Named standards on every check

  • Clause on every result

    Formula, inputs and reference visible

What it calculates

Design flexible wood structural panel diaphragms to SDPWS 2021 with LRFD. Loads are distributed to any number of braced wall lines by FEA, then checked for unit shear capacity, aspect ratio, chord and collector forces to NDS 2024, nailing zones and in-plane deflection. Wind and seismic loads link in from the wind and seismic calculations.

Who uses this calculator

US engineers designing wood structural panel diaphragms for wind and seismic, who now distribute loads, pick sheathing and nailing from SDPWS tables, and check chords, collectors and deflection by hand or in spreadsheets. Wind and seismic loads link in from the wind and seismic calculations.

Replaces roughly 2 to 4 hours of hand calculation per diaphragm, covering load distribution to braced wall lines, SDPWS capacity lookups, and chord, collector and deflection checks.

How it calculates

The calculator distributes wind and seismic loads through a flexible wood structural panel diaphragm to its braced wall lines, then designs the sheathing, nailing, chords and collectors and checks the in-plane deflection.

Load distribution

Wind loads are entered as pressures over a tributary height, and seismic loads as total point loads or line loads. Seismic point loads are spread uniformly over the length you specify. A finite element analysis distributes the combined line loads to any number of braced wall lines, treating each span between wall lines as simply supported. The strength load combinations of ASCE 7-22 Section 2.3 give the design wind and seismic shear and moment from 1.0W and 1.0E.

Unit shear capacity

The nominal unit shear capacity v_n comes from SDPWS 2021 Tables 4.2A and 4.2C, for the selected sheathing and nailing, edge blocking, panel layout case and nail spacing. Framing with a specific gravity below 0.5 reduces it through the specific gravity adjustment factor (Footnote 2 to those tables). The adjusted capacity is multiplied by the LRFD resistance factor for seismic (SDPWS 2021 Section 4.1.4.1) and for wind (Section 4.1.4.2), giving separate seismic and wind design capacities.

Diaphragm shear utilization = unit shear demand / unit shear capacity ≤ 1.0, for the governing of wind and seismic.

Aspect ratio

The ratio of the largest span to the diaphragm width is limited to 4 for blocked and 3 for unblocked wood structural panel diaphragms (SDPWS 2021 Section 4.2.2 and Table 4.2.2).

Nailing zones

With uniform nailing, the selected spacing applies across the whole diaphragm. With two zones, Zone A keeps that spacing next to each braced wall line and Zone B uses a lighter spacing further out. The minimum Zone A length is the largest distance from a wall line at which the required unit shear still exceeds the adjusted Zone B capacity.

Chords and collectors

Chord force is the design moment divided by the diaphragm width. Chords are sawn dimension lumber designed to NDS 2024 LRFD for dry service, with a time effect factor of 1.0. Tension capacity uses the gross area of the continuous plies (NDS 2024 Section 3.8.1). Compression capacity includes the column stability factor C_P with c = 0.8, for buckling about the narrow face over the chord unbraced length (Sections 3.6.3 and 3.7.1). The sheathing braces the chord in the plane of the diaphragm.

The collector force along each braced wall line is the line reaction multiplied by one minus the ratio of shear wall length to diaphragm width. Where the wall top plates act as both chords and collectors, collectors are checked with the same member. A collector seismic force factor applies to seismic collector forces: 1.0 where the structure is braced entirely by light-frame wood shear walls, or the overstrength factor or 1.5 you enter otherwise (ASCE 7-22 Sections 12.10.2.1 and 12.10.3.4).

Deflection

For blocked, uniformly nailed diaphragms, mid-span deflection of the largest span uses the four-term equation of SDPWS 2021 Commentary Section C4.2.3:

Δ = bending + panel shear + nail slip + chord splice slip

It is evaluated at the larger of the wind and seismic strength-level unit shears. Nail slip comes from the commentary equations at the load per nail, or from a value you enter, with green framing selecting the green lumber equation. You can compare the result with a deflection limit set from drift, compatibility or serviceability needs.

Out of scope

Rigid and semi-rigid diaphragms, torsion, chord splices, collector connections, holdowns and the net section at bolted splices are not designed. Deflection is not calculated for unblocked diaphragms.

What engineers say

Engineer

“The steel beam calc, wind load and shear wall calcs and retaining wall calc are also amazing! All the calculators are much more user friendly than other programs/Excel sheets I have used in the past.”

John C.

Structural Engineer

Frequently asked questions

Access this calculator and 100+ more

All verified, standards-aligned. Start a free trial - no credit card required.

Linking a calculation to a column in Calcs.com, with the AISC Steel Construction Manual reference attached

We use analytics cookies to understand how you use this site and improve our content. See our privacy policy and cookie policy for details.