Free tools
Free beam calculator for Australian spans
- Free · No sign-up required
- Instant results
- FEA-powered
No credit card required · 200+ calculators · All major codes
Model bending moment, shear force and deflection in metric units. Simple, continuous, cantilever and propped spans, with no sign-up required.
How to use the free beam calculator
No credit card required.
- [ 01 ]
Enter beam geometry
Set the span length L in mm, elastic modulus E in MPa, second moment of area I_x in mm⁴, and cross-sectional area A in mm². Defaults are 2,000 mm and a 150 UB 14.0 at 200,000 MPa.
- [ 02 ]
Set your supports
Add fixed, pinned or roller supports at any position along the beam. A support set away from the ends creates a cantilever, so overhanging and propped beams are entered the same way.
- [ 03 ]
Apply loads
Add point loads in kN and distributed loads in kN/m. Unequal start and end magnitudes give a linearly varying load, and locations inside the span give a partial load.
- [ 04 ]
Read the diagrams
Moment in kN·m, shear in kN and deflection in mm update instantly. Per-span moments and per-support reactions are tabulated below the diagrams.
Is this beam calculator free?
The Calcs.com beam calculator is free, runs in your browser and needs no sign-up. It solves simply supported, cantilever, propped and continuous beams in metric units, with any number of spans. Supports can be fixed, pinned or roller, and loads can be point, uniform, partial or linearly varying.
A finite element solver draws bending moment (kN·m), shear (kN) and deflection (mm) diagrams along the full length and lists the support reactions.
Checking a section to AS 4100, AS 1720.1 or AS 3600 needs a paid Calcs.com plan. Every plan starts with a 14-day free trial, with no credit card.
About this calculator
Solve simple, continuous, cantilever and propped beams in metric units. Enter the span, section stiffness, supports and loads. A finite element solver returns bending moment, shear force and deflection along the full length. Per-span moments and per-support reactions are tabulated underneath. The analysis is code independent, so the same model holds under AS 4100, AS 1720.1 and AS 3600. Design checks against those standards need a paid Calcs.com plan, which starts with a 14-day free trial.
Simply supported, uniform load: M = wL² / 8
Simply supported, uniform load: V = wL / 2
Simply supported, uniform load: δ = 5wL⁴ / 384EI
Simply supported, central point load: M = PL / 4
Simply supported, central point load: δ = PL³ / 48EI
Bending stress from moment: σ = M / S, where S = I_x / c
Validated against:
- Connor (2013), Fundamentals of Structural Engineering, Example 3.13: a two-span beam with an internal hinge under opposing triangular loads. Solver moment agrees to within 0.3%, shear and support reactions match exactly.
Last reviewed
How to size a steel beam
Size a steel beam from two targets: the section modulus that strength needs and the second moment of area that deflection needs. The Calcs.com free beam calculator gives you the bending moment and deflection. The lightest section that meets both targets is the starting point for a full AS 4100 design check.
- Analyze the beam twice. Run the strength combination (1.2G + 1.5Q) for the design moment M*. Run the short-term serviceability combination (G + ψs Q) for deflection.
- Find the strength target. For a compact section with continuous lateral restraint to the compression flange, Ze ≥ M* / (φ fy), with φ = 0.9.
- Find the stiffness target. Rearrange δ = 5wL⁴ / 384EI to get Ix ≥ 5wL⁴ / (384 E Δallow).
- Pick the lightest section that meets both. Then check it fully: member moment capacity, shear, web bearing and self-weight.
Worked example: 6 m floor beam
A simply supported Grade 300PLUS UB spans 6 m and carries a residential floor over a 3 m load width, at G = 1.5 kPa and Q = 1.5 kPa. The floor restrains the top flange, and each end sits on 150 mm of bearing.
- Strength: 3 m × (1.2 × 1.5 + 1.5 × 1.5) kPa = 12.15 kN/m, so M* = 12.15 × 6² / 8 = 54.7 kN·m.
- Strength target: Ze ≥ 54.7 × 10⁶ / (0.9 × 320) = 190 × 10³ mm³.
- Stiffness target: short-term deflection at G + 0.7Q = 7.65 kN/m, limited to L/250 = 24 mm, needs Ix ≥ 26.9 × 10⁶ mm⁴.
- Deflection governs the choice. The lightest UB with Ix ≥ 26.9 × 10⁶ mm⁴ is a 250 UB 25.7 (Ix = 35.4 × 10⁶ mm⁴, Ze = 319 × 10³ mm³).
The Calcs.com AS 4100 steel beam calculator confirms the section: short-term deflection 18.2 mm against 24 mm allowed (76%), and bending at 60% (φMs = 91.9 kN·m).
It also catches what hand sizing does not. On 50 mm of bearing, the unstiffened web fails in bearing at the supports. It passes at 150 mm of bearing length, at 86%. Hand sizing chooses a section; the full design check shows how it sits on its supports.
Check your section in the AS 4100 steel beam calculator
How far a steel beam can span
A steel beam spans as far as its first limit allows: bending strength, deflection or bearing at the supports. Find it in the Calcs.com free beam calculator by fixing the section and load, then lengthening the beam until deflection or moment reaches its limit.
Deflection grows with the fourth power of span. A 250 UB 25.7 floor beam carrying G = 4.5 kN/m and Q = 4.5 kN/m deflects 18.2 mm short-term at 6 m. At 6.5 m it deflects 25.1 mm against 26.0 mm allowed by L/250. At 7 m it reaches 33.8 mm against 28 mm, and fails. Bending would not run out until about 7.8 m.
So this section spans about 6.5 m at this load. The longer span raises the reactions too: the Calcs.com AS 4100 steel beam calculator puts web bearing at 93% on 150 mm of bearing at 6.5 m, so it still passes.
How to calculate the load on a beam
The load on a beam is the floor or roof pressure multiplied by the load width the beam carries. For evenly spaced beams, the load width is the beam spacing.
w = pressure × load width
Beams at 3 m centers carrying G = 1.5 kPa and Q = 1.5 kPa take 4.5 kN/m of each. Enter those as distributed loads in the Calcs.com free beam calculator. Factor them for strength (1.2G + 1.5Q = 12.15 kN/m) and use G + 0.7Q (7.65 kN/m) for short-term deflection.
Inside the calculator
The Calcs.com beam calculator takes the geometry and loading of a beam and returns bending moment, shear and deflection diagrams, plus maximum demands, from a finite element analysis engine. Results update as you type. This page loads the calculator in metric units.
The solver works from the section stiffness you enter rather than a section type, so it handles any prismatic member: a rolled steel I-beam or RSJ, a timber joist, a concrete beam, or a built-up shape. Enter the area and second moment of area and the analysis is the same.
The analysis itself is code independent: it solves statics and stiffness, so the same model holds under AS, NZS, Eurocode, CSA and US standards. Design checks against a specific standard need a paid Calcs.com plan, which adds design in steel, concrete and timber to AS 4100, AS 3600 and AS 1720.1. Every plan starts with a 14-day free trial, no credit card required.
Inputs and outputs at a glance
| Quantity | Symbol | Unit | Default |
|---|---|---|---|
| Length of beam | L | mm | 2,000 mm |
| Young's modulus | E | MPa | 200,000 MPa |
| Area of cross-section | A | mm² | 1,780 mm² |
| Second moment of area | I_x | mm⁴ | 6,660,000 mm⁴ |
| Point load | P | kN | none |
| Distributed load | w | kN/m | 0.1 kN/m rising to 1 kN/m |
| Moment demand | M* | kN·m | calculated |
| Shear demand | V* | kN | calculated |
| Deflection | δ | mm | calculated |
| Maximum reaction | R* | kN | calculated |
Frequently asked questions
Get more functionality with a free Calcs.com trial
Start a 14-day free trialThis calculator is free. A 14-day trial adds design checks for the beam you just analyzed:
- Steel beam design to AS 4100
- Concrete beam design to AS 3600
- Timber beam design to AS 1720.1
We use analytics cookies to understand how you use this site and improve our content. See our privacy policy and cookie policy for details.