Wood Roof Tie (LRFD)

NDS 2024LRFDFlag of United States

The easy to use online Calcs.com Wood Roof Tie LRFD Calculator to NDS 2024 enables you to do quick and powerful design and analysis for wood collar ties and rafter ties. Choose from our library of thousands of common wood sections, or create your own and get instant results with our easy to understand traffic light checks for tension in the ties and all limit states for the rafters.

14-day free trial • No credit card required

  • NDS 2024 (LRFD)

    Named standard on every check

  • Clause on every result

    Formula, inputs and reference visible

  • Updated 21 Aug 2026

    Version 3, latest calculation change

  • 250+ calculations

    In 2026 across 130+ organizations

Start from your design scenario, not a generic setup

Each preset sets up this calculator for one design scenario, with the inputs that scenario usually takes already filled in. You change what differs on your project instead of re-entering every value on every job.

  • Collar Tie
  • Rafter Tie
  • Collar & Rafter Tie

What it calculates

The easy to use online Calcs.com Wood Roof Tie LRFD Calculator to NDS 2024 enables you to do quick and powerful design and analysis for wood collar ties and rafter ties. Choose from our library of thousands of common wood sections, or create your own and get instant results with our easy to understand traffic light checks for tension in the ties and all limit states for the rafters.

Who uses this calculator

Rafter loads link directly from connected calculations in your project - change a load or span and this tie design updates automatically. Designs collar ties and rafter ties to NDS 2024 LRFD, checking factored tie tension and all rafter limit states using ASCE 7 factored load combinations with NDS 2024 φ-factors and format conversion factors.

How it calculates

The Wood Roof Tie (LRFD, NDS 2024) calculator designs collar ties and rafter ties as a coupled rafter-and-tie assembly under the Load and Resistance Factor Design provisions of the 2024 National Design Specification for Wood Construction. The calculator solves this geometry simultaneously, computing the tie tension and the rafter moment diagram as a function of roof pitch, rafter span, and tie height.

Roof geometry and horizontal thrust

The horizontal outward thrust from the pitched rafter is derived from the slope angle and the tributary load. For a symmetric gable with pitch angle α:

H = (w × Lh) / (2 × tan(α)) × (1 / cos(α))

Where w is the tributary load per unit of rafter slope length and Lh is the horizontal rafter run. The horizontal thrust H equals the tie tension when the tie is at plate level. Placing the tie higher (collar tie configuration) reduces the tie force because the lower rafter segment carries its own horizontal component, but it increases the unbraced rafter span above the tie, raising bending demand. The calculator assumes symmetrical geometry - applied loads and framing are equal on both sides of the ridge.

Factored tie tension check

The factored tensile resistance of the tie member is:

φtTn = φt × KF,t × λ × Ft × CM × Ct × CF × Ci × Anet

Where:

  • φt = 0.80 is the NDS LRFD tension resistance factor
  • KF,t = 2.70 is the format conversion factor for tension parallel to grain (from NDS 2024 Table N1)
  • λ is the time effect factor for the governing load combination
  • Ft is the tabulated reference tensile design value from the NDS Supplement tables for the selected species and grade
  • CM, Ct, CF, Ci are the wet service, temperature, size, and incising adjustment factors

The tension utilization check is:

Tu / φtTn ≤ 1.0

Connection design - nails, bolts, or metal straps at the tie-to-rafter interface - is the responsibility of the engineer and is not checked by this calculator.

Rafter bending check

The factored moment resistance is:

φbMn = φb × KF,b × λ × Fb × CM × Ct × CF × Cfu × Ci × Cr × CL × S

Where:

  • φb = 0.85 is the NDS LRFD flexure resistance factor
  • KF,b = 2.54 is the format conversion factor for bending (from NDS 2024 Table N1)
  • CL is the beam stability factor for lateral-torsional buckling - the rafter top face is assumed to be continuously braced by roof sheathing, which suppresses LTB on the compression face and permits CL = 1.0 for standard framing with adequate sheathing attachment
  • Cr = 1.15 applies when three or more rafters at 24 in. spacing or less share a load-distributing element

The bending check is:

Mu / φbMn ≤ 1.0

Rafter shear check

The factored shear resistance is:

φvVn = φv × KF,v × λ × Fv × CM × Ct × Ci × (2/3) × A

Where φv = 0.75 is the shear resistance factor and KF,v = 2.88 is the format conversion factor for shear (from NDS 2024 Table N1). The check is:

Vu / φvVn ≤ 1.0

Rafter bearing check

At the wall plate, the rafter bears perpendicular to grain. The factored bearing resistance is:

φcRn = φc × KF,c⊥ × Fc⊥ × CM × Ct × Ci × Cb × Abearing

Where φc = 0.90 is the compression resistance factor for bearing and Cb is the bearing area factor from NDS 2024 §3.10.4. The bearing check is:

Ru / φcRn ≤ 1.0

Deflection checks

Two deflection limit states are verified using unfactored (service-level) loads, consistent with NDS LRFD practice for serviceability:

  • Short-term (ST): instantaneous elastic deflection under the specified live or snow load combination, checked against the user-defined span-ratio limit (default L/360).
  • Long-term (LT): total deflection including creep, computed as the ST deflection amplified by the applicable creep factor for the in-service moisture condition, checked against the user-defined limit (default L/240).

Time effect factor and load combinations

For each ASCE 7 factored load combination, the calculator identifies the shortest-duration load type that contributes meaningfully to the demand and applies the corresponding λ. This means a snow-governed combination (e.g. 1.2D + 1.6S) applies λ = 1.0, while a wind-governed combination (e.g. 0.9D + 1.0W) applies λ = 1.25. The governing combination - the one producing the highest utilization ratio after accounting for both the factored demand and the factored resistance - is reported for each limit state.

NDS 2024 vs. NDS 2018

This version follows NDS 2024 and defaults its load combinations to IBC 2024. Reference design values come from the NDS Supplement tables for the selected species and grade. If your jurisdiction still references NDS 2018, use the timberRoofTieLRFD calculator instead.

What engineers say

Engineer
PWI

“The load linking feature is huge for us. Before, we had to use separate calculators and manually input everything.”

Noah Diaz

Engineering Design Coordinator, PWI

Engineer
Dynamic Analysis Engineering Consulting

“Just the simple feature of being able to link loads is a really big time-saver.”

Sam Hensler

Principal, Dynamic Analysis Engineering Consulting

Frequently asked questions

Access this calculator and 100+ more

All verified, standards-aligned. Start a free trial - no credit card required.

Linking a calculation to a column in Calcs.com, with the AISC Steel Construction Manual reference attached

We use analytics cookies to understand how you use this site and improve our content. See our privacy policy and cookie policy for details.