What sizes does Carter Holt Harvey Woodproducts LVL come in?

Calcs.com carries 70 Carter Holt Harvey Woodproducts sections across hySPAN, hySPAN+, hy90, hyONE and hyCHORD. Depths run from 90 mm to 600 mm (90, 120, 130, 140, 150, 170, 190, 200, 240, 290, 300, 360, 400, 450, 525, 600 mm), in breadths of 35, 45, 63, 75, 90 mm. Every one of those sections is selectable in the calculators listed on this page.

Is there a span table for Carter Holt Harvey Woodproducts LVL?

This page publishes section properties and characteristic values, not allowable spans. A span is not a property of the section: it depends on the loads you apply, the member spacing, and the deflection limit you design to, so the same section spans different distances on different jobs. Rather than reading a span off a generic table, select the Carter Holt Harvey Woodproducts section in a Calcs.com calculator and enter your actual loads. The calculator checks bending, shear, bearing, and deflection and reports the governing limit.

What are the characteristic values for Carter Holt Harvey Woodproducts hySPAN+?

hySPAN+ is published with modulus of elasticity 14,000 MPa, characteristic shear strength 4.6 MPa, compression parallel to grain 41 MPa and approximate density 650 kg/m3. Characteristic bending strength varies with depth, from 42.1 MPa to 50 MPa across the sizes in the table above. Values are taken from Futurebuild LVL Specific Design Guide (Aug 2019) and hySPAN and hySPAN+ Specification Sheet (Oct 2012); weak axis values per Futurebuild LVL NZ Engineering Design Guide (Aug 2019), so check them against the manufacturer's current design guide before you rely on them.

What are the characteristic values for Carter Holt Harvey Woodproducts hy90?

hy90 is published with modulus of elasticity 9,500 MPa, characteristic shear strength 4.6 MPa, compression parallel to grain 36.6 MPa and approximate density 625 kg/m3. Characteristic bending strength varies with depth, from 27.2 MPa to 31.7 MPa across the sizes in the table above. Values are taken from Futurebuild LVL Specific Design Guide (Aug 2019) and hySPAN and hySPAN+ Specification Sheet (Oct 2012); weak axis values per Futurebuild LVL NZ Engineering Design Guide (Aug 2019), so check them against the manufacturer's current design guide before you rely on them.

What are the characteristic values for Carter Holt Harvey Woodproducts hyONE?

hyONE is published with modulus of elasticity 16,000 MPa, characteristic shear strength 4.6 MPa, compression parallel to grain 48 MPa and approximate density 625 kg/m3. Characteristic bending strength varies with depth, from 52.1 MPa to 56.4 MPa across the sizes in the table above. Values are taken from Futurebuild LVL Specific Design Guide (Aug 2019) and hySPAN and hySPAN+ Specification Sheet (Oct 2012); weak axis values per Futurebuild LVL NZ Engineering Design Guide (Aug 2019), so check them against the manufacturer's current design guide before you rely on them.

What are the characteristic values for Carter Holt Harvey Woodproducts hyCHORD?

hyCHORD is published with modulus of elasticity 11,000 MPa, characteristic shear strength 4.4 MPa, compression parallel to grain 32.6 MPa and approximate density 600 kg/m3. Characteristic bending strength varies with depth, from 36 MPa to 40 MPa across the sizes in the table above. Values are taken from Futurebuild LVL Specific Design Guide (Aug 2019) and hySPAN and hySPAN+ Specification Sheet (Oct 2012); weak axis values per Futurebuild LVL NZ Engineering Design Guide (Aug 2019), so check them against the manufacturer's current design guide before you rely on them.

Does Calcs.com support Carter Holt Harvey Woodproducts products?

Yes. 70 Carter Holt Harvey Woodproducts sections are built into the section library, so you select them from a dropdown rather than entering properties by hand. They are available in 10 calculators, listed on this page.

Carter Holt Harvey Woodproducts hySPAN LVL sizes

Q: What are the characteristic values for Carter Holt Harvey Woodproducts hySPAN?

hySPAN is published with modulus of elasticity 13,200 MPa and characteristic shear strength 4.6 MPa. Characteristic bending strength varies with depth, from 37.6 MPa to 50 MPa across the sizes in the table above. Values are taken from Futurebuild LVL Specific Design Guide (Aug 2019) and hySPAN and hySPAN+ Specification Sheet (Oct 2012); weak axis values per Futurebuild LVL NZ Engineering Design Guide (Aug 2019), so check them against the manufacturer's current design guide before you rely on them.

Calcs.com carries 70 Carter Holt Harvey Woodproducts LVL sections across 10 calculators. The section properties and characteristic values are the ones Carter Holt Harvey Woodproducts publishes.

Design a beam now See every size

No credit card required

Carter Holt Harvey Woodproducts

Carter Holt Harvey Woodproducts products are in the Calcs.com section library because engineers specify them. Claim this page to connect your sales team, confirm your published values, and see which calculations use your products.

Is this your company? Claim this page

Every Carter Holt Harvey Woodproducts LVL section

All 70 Carter Holt Harvey Woodproducts sections in the Calcs.com library, with the section properties and characteristic values used to design them.

These are section properties and characteristic values, not allowable spans. A span depends on your loads, member spacing, and deflection limit, so it has to be calculated.

Carter Holt Harvey Woodproducts hySPAN LVL

45 sections. Depths: 90, 130, 150, 170, 200, 240, 300, 360, 400, 450, 525, 600 mm. Breadths: 35, 45, 63, 75 mm.